Page 1 of 1

New boat/ bilge pump question/other question

Posted: Sat Apr 02, 2011 10:55 pm
by johnsgonefishin
I just bought a new to me(used) starcraft 14ft boat. I rigged a starting battery, and a deep cycle (for electric motor) as well as an onboard minnkota charger. Do I need a bilge pump or should I get one? I have the power to run one, and My outboard charges my starting battery while running.

I plan on fishing little lakes mainly, but occasional trips to lake roosevelt or fort spokane, courde alene(maybe calm days), calm parts of the snake, columbia will not be out of the question. I have also seen some hairy situations on Rock lake.

When I was at a boat outfitter store the guy there said just get a bucket, but for me if its under $100 I would rather flip a switch. I also thought about one of the manual pumps like the squirt gun.

Also is it hard to build a casting platform up front. I have bench seating right now.

RE:New boat/ bilge pump question/other question

Posted: Sat Apr 02, 2011 11:04 pm
by Amx
ALWAYS good to have an automatic bilge pump. Or at least one you can flip a switch and make it work while you use a bucket to help, if necessary. Get a collapsing bucket, doesn't take up much room at all.

RE:New boat/ bilge pump question/other question

Posted: Sun Apr 03, 2011 2:00 am
by wishniwasfishn
I would have to agree with AMX a small bilge pump can come in handy if you get stuck in the rain or just take on some water over the side it is very nice to be able to get that water back out, I also added a small pump to my Invader and we were at Priest Lake and it rained heavily all night one night and when I went down to my boat the next morning it took about 6-7 minutes of pumping to get all that water out. Hope this helps, Dennis

RE:New boat/ bilge pump question/other question

Posted: Mon Apr 04, 2011 2:35 am
by johnsgonefishin
Thank you, I will look at getting a small bilge pump.

I have another add on question. I have 2 batteries, one marine starter/ one deep cycle. I also have the onboard charger. I am currently runing the minnkota to the deep cycle. I run the outboard and fish finder to the marine starter. I am looking at adding lights to the marine starter as well as the bilge pump. Right now I currently unhook the motor and fish finder when I charge/ rehook up when I go back out. Do I need a switch for each battery? If I set up the switches do I run the charger into one of the switches or do I keep it seperate and disconnect the switch when I hook up the charger. Any switch recomendations or do I not need one. Thanks again, this is my second boat but my first was really basic.

RE:New boat/ bilge pump question/other question

Posted: Mon Apr 04, 2011 2:41 am
by Amx
With one charger you run the leads to the switch, then 2 sets of wires - one set to each battery - from each side of the 2 position switch - left = batt 1, center = off, right = batt 2. Personaly I'd get another charger, a 2 bank one. Charge both batteries at the same time. It's worth the expense. Been there, done that, now I use a 3 bank on-board charger.

RE:New boat/ bilge pump question/other question

Posted: Mon Apr 04, 2011 3:10 pm
by Anglinarcher
johnsgonefishin wrote:I just bought a new to me(used) starcraft 14ft boat. I rigged a starting battery, and a deep cycle (for electric motor) as well as an onboard minnkota charger. Do I need a bilge pump or should I get one? I have the power to run one, and My outboard charges my starting battery while running.

I plan on fishing little lakes mainly, but occasional trips to lake roosevelt or fort spokane, courde alene(maybe calm days), calm parts of the snake, columbia will not be out of the question. I have also seen some hairy situations on Rock lake.

When I was at a boat outfitter store the guy there said just get a bucket, but for me if its under $100 I would rather flip a switch. I also thought about one of the manual pumps like the squirt gun.

Also is it hard to build a casting platform up front. I have bench seating right now.
Yes, and no. LOL

You can build a casting platform up front, I did it years ago on a 14' Starcraft, so it can be done. You will probably end up adding a fair amount of weight to the boat in the process, but it can be done.

I like bilge pumps, but even now I still keep a bail bucket on board. I have been in rain storms that were just nasty, and it was nice to flip the switch on the bilge and let it do the work. I have also had those days where the waves would occasionally add to the problem. Yes, the bilge is nice.

But, they can fail, and if that is your only method of removing water, it can get nasty out there. If you get the bilge, exercise it once in a while so it does not get filled with sand or wasp next. LOL

RE:New boat/ bilge pump question/other question

Posted: Mon Apr 04, 2011 11:49 pm
by johnsgonefishin
Amx wrote:With one charger you run the leads to the switch, then 2 sets of wires - one set to each battery - from each side of the 2 position switch - left = batt 1, center = off, right = batt 2. Personaly I'd get another charger, a 2 bank one. Charge both batteries at the same time. It's worth the expense. Been there, done that, now I use a 3 bank on-board charger.
The charger I have charges both batteries at the same time. Can I leave all the electronics hooked up at the same time(ie fish finder/motor) or should I have a switch or disconnect them while charging/using/ or not using?

RE:New boat/ bilge pump question/other question

Posted: Tue Apr 05, 2011 12:00 am
by Amx
You should be able to leave them hooked up at all times. Mine is designed that way. It doesn't have alligator clips, it has lugs that get bolted to the batt terminals along with the regular wires. You can leave everything hooked up.

RE:New boat/ bilge pump question/other question

Posted: Wed Apr 06, 2011 12:27 am
by aaron42ash
I was planning to get a jon with bench seating and add a casting platform as well. Check out this link. The guy here made one out of an old aluminum ladder, which can cut down on the weight significantly.


Jon Boat Mods.
More Mods.



I just got a livewell aireator (500GPH), which suctions to the inside of an existing livewell, or a large cooler for livewell use. Because it's only suctioned in there, it can be removed and used as a bilge. Whole set-up with tube, wires, aireator poles and pump was only 39.99. Good luck with your project